Recent questions tagged microprocessor-8085

Statement for Linked Answer Questions $81 a$ and $81 b$:Consider an $8085$ microprocessor systemIf in addition following code exists from $019 \mathrm{H}$ onwards,$\text{...

In an $8085 \; \mu \; \mathrm{P}$ system, the $\text{RST}$ instruction will cause an interruptonly if an interrupt service routine is not being executedonly if a bit in t...

The following insturctions have been executed by an $8085 \; \mu \mathrm{P}$$\begin{array}{cl}\text { ADDRESS (HEX) } & \text { INSTRUCTION } \\ 6010 & \text { LXI H, 8A ...

While moving data between registers of the $8085$ and the stack(1) a $\text{PUSH}$ instructionPre increments the stack pointer(2) a $\text{POP}$ instructionPost increment...

An $8085 \; \mu \mathrm{P}$ uses a $2 \; \mathrm{MHz}$ crystal. Find the time taken by it to execute the following delay subroutine, inclusive of the call instruction in ...

The number of hardware interrupts (which require an external signal to interrupt) present in an $8085$ microprocessor are$1$$4$$5$$13$

In the $8085$ microprocessor, the $\text{RST6}$ instruction transfers the program execution to the following location:$30 \mathrm{~H}$$24 \mathrm{~H}$$48 \mathrm{~H}$$60 ...

The contents of Register $\text{(B)}$ and Accumulator $\text{(A)}$ of $8085$ microprocessor are $49 \mathrm{H}$ and $3 \mathrm{AH}$ respectively. The contents of $\mathrm...

(a) The program and machine code for an $8085$ microprocessor are given by$\begin{array}{lll}3 \mathrm{E} & \text {MVI} & \text {A} \\ \text {C3} & & \\ 00 & \text {NOP} ...

If $\text{CS}=\text{A}_{15} \; \text{ A}_{14} \; \text{A}_{13}$ is used as the chip select logic of a $4 \; \text{K RAM}$ in an $8085$ system, then its memory range will ...

An $8085$ assembly language program is given below$\begin{array}{ll} & \text{ MVIC, 03H } \\ & \text { LXIH, 2000H } \\ \text { LOOP : } & \text { MOV A, M } \\ & \text {...

Consider the following sequence of instructions for an $8085$ microprocessor based system.$\begin{array}{lll} \text{Memory Address} & \text{Instructions} \\ \text{FF00} &...

Consider the following assembly language program.$\begin{array}{rll} \text { MVI } & \text { B,87H } \\ \text { MOV } & \text { A, B } \\ \text { START : JMP } & \text { ...

An $8085$ microprocessor operating at $5 \; \mathrm{MHz}$ clock frequency executes the following routine.$\begin{array}{lll} {\text{START:}} & \text{MOVE} & \text{A,B} \\...

Write a short assembly language program, without using any arithmetic instruction, to store hexadecimal $5D$ in the flag register of $8085$ microprocessor. Data in other ...

In an $8085$ microprocessor, the instruction CMP $B$ has been executed while the content of the accumulator is less than that of register $B$. As a resultCarry flag will ...

The $8255$ Programmable Peripheral Interface is used as described below.An A/D converter is interfaced to a microprocessor through $8255.$ The conversion is initiated by ...

The number of memory cycles required to execute the following $8085$ instructions$\text{LDA 3000 H}$$\text{LXI D, FOF 1 H}$would be$2$ for (I) and $2$ for (II)$4$ for (I)...

Consider the sequence of $8085$ instructions given below.$\text{LXI H, 9258, MOV A, M, CMA, MOV M, A}$Which one of the following is performed by this sequence?Contents of...

It is desired to multiply the numbers $0 \mathrm{AH}$ by $0 \mathrm{BH}$ and store the result in the accumulator. The numbers are available in registers $B$ and $C$ respe...

Statement for Linked Answer Questions 81 a and 81 b:Consider an $8085$ microprocessor systemThe following program starts at location $0100 \mathrm{H}$.$\begin{array}{l} \...

The total number of memory accesses involved (inclusive of the $op$ – code fetch) when an $8085$ processor executes the instruction $\text{LDA}$ $2003$ is$1$$2$$3$$4$

The following sequence of instructions are executed by an $8085$ microprocessor:$\begin{matrix}1000 &LXI & SP &27 \; FF \\ 1000 &CALL & & 1006\\ 1006 &POP \; H & & \...

An $\frac{\mathrm{I}}{\mathrm{O}}$ peripheral device shown in Figure $(b)$ below is to be interfaced to an $8085$ microprocessor. To select the $\frac{\mathrm{I}}{\mathrm...

Following is the segment of a $8085$ assembly language program$\text{LXISP,EFFFH}$$\text{CALL 3000 H}$$3000 \mathrm{H}: \mathrm{LXIH}, 3 \mathrm{CF} 4 \mathrm{H}$$\text{P...

An $8255$ chip is interfaced to an $8085$ microprocessor system as an $\mathrm{I} / \mathrm{O}$ mapped $\mathrm{I} / \mathrm{O}$ as shown in the figure. The address lines...

An $8085$ assembly language program is given below.Line 1: MVI A, B5H 2: MVI B, 0EH 3: XRI 69H 4: ADD B 5: ANI 9BH 6: CPI 9FH 7: STA 3010H 8: HLT After execution of line ...

An $8085$ executes the following instructions$\begin{array}{lll}2710 & \text { LXI} & \text{H,} & \text{30A0H } \\2713 & \text { DAD} & \text{H } \\2714 & \text { PCHL ...

In a microprocessor, the service routine for a certain interrupt starts from a fixed location of memory which cannot be externally set, but the interrupt can be delayed o...

For the $8085$ assembly language program given below, the content of the accumulator after the execution of the program is$$\begin{array}{|lll|}\hline 3000 & \text{MVI} &...